WPMAG - EUROfusion Working Packages Magnets system
→
UTC
Bruno Brunelli Hall (Frascati)
Bruno Brunelli Hall
Frascati
ENEA - Research Centre
Via Enrico Fermi, 45
Frascati, Italy
Organizers
Registration
Registration form
48
/ 60
Participants
-
-
11:00
→
11:10
Welcome 10m Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, ItalySpeaker: C. Vorpahl -
11:10
→
11:40
Introduction to Prospective R&D 30m Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, ItalySpeaker: R. Kembleton -
11:40
→
12:25
Prospective R&D: session 1 Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy-
11:40
Test of HTS tapes 15m
Task: ENR-PRD.MAG-T012
Speaker: Klaus-Peter Weiss -
11:55
Progress in chemical HTS tape preparation 15m
Task: ENR-PRD.MAG-T013
Speaker: Michael Wolf -
12:10
Conceptual Design of an HTS TF coil for DEMO 15m
Task: ENR-PRD.MAG-T014
Speaker: Reinhard Heller
-
11:40
-
12:25
→
13:40
Lunch 1h 15m ENEA Canteen
ENEA Canteen
-
13:40
→
16:10
Prospective R&D: session2 Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy-
13:40
Neutron irradiation investigation on HTS tapes 15m
Task: ENR-PRD.MAG-T015
Speaker: Michael Eisterer (TU Wien) -
13:55
Neutron Irradiation investigation on HTS tapes 15m
Task: ENR-PRD.MAG-T016
Speaker: Miloš Jirsa -
14:10
Experiments and FE Modeling of stress-strain and AC loss in HTS cables 15m
Task: ENR-PRD.MAG-T017
Speaker: Arend Nijhuis (University of Twente) -
14:25
Measurements and Electromechanical model of Twisted stacks 15m
Task: ENR-PRD.MAG-T021
Speaker: Xavier Granados -
14:40
HTS tapes Jc (B,T) characterization 15m
Task: ENR-PRD.MAG-T018
Speaker: Michal Vojenčiak (Institute of Electrical Engineering SAS, Bratislava) -
14:55
Mechanical FEM model of CORC cable 15m
Task: ENR-PRD.MAG-T020
Speaker: Michal Vojenčiak (Institute of Electrical Engineering SAS, Bratislava) -
15:10
Mech. FEM model of stress on sub-cables of conductor for CS based on CORC cables 15m
Task: ENR-PRD.MAG-T019
Speaker: Michal Vojenčiak (Institute of Electrical Engineering SAS, Bratislava) -
15:25
EXTRA - Report on direct spooling of partially equipped CroCos 15m
Task: ENR-PRD.MAG-T022
Speaker: Walter Fietz (KIT / ITEP) -
15:40
General discussion on TS 15mSpeaker: All
-
15:55
PRD activities: meeting conclusions 15mSpeaker: All
-
13:40
-
16:10
→
16:25
Coffee break 15m F23 hall
F23 hall
-
16:25
→
18:05
Cable R&D and Tests (AMT 5.3 & 5.5): Session 1 Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy-
16:25
Status of the SULTAN preparation for the HTS quench experiments 15mSpeaker: Pierluigi Bruzzone
-
16:40
Development of high-current HTS cables at KIT 15m
Task: MAG-5.3-T016
Speaker: Walter Fietz -
16:55
Tests on high-current HTS cables 15m
Task: MAG-5.5-T006
Speaker: K-P Weiss + Daniel Nickel -
17:10
HTS conductor design and development at SPC 15m
Task: MAG-5.3-T017
Speakers: Ortensia Dicuonzo, Uglietti -
17:25
Development of high-current HTS cables at ENEA 15m
bb
Speaker: Dr Andrea Augieri (ENEA) -
17:40
General discussion on TS 15mSpeaker: All
-
17:55
Conclusion 5m
-
16:25
-
11:00
→
11:10
-
-
09:00
→
10:15
General Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy-
09:00
Update on EUROfusion context 30mSpeaker: C. Vorpahl
- 09:30
-
09:00
-
10:15
→
10:45
WP Design Session Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy-
10:15
ENEA TF winding pack design 15m
MAG-2.1-T027
Speaker: Giordano Tomassetti (ENEA) -
10:30
CEA TF winding pack designs (WP#3 and WP#4) 15m
MAG-2.1-T026
Speaker: Louis ZANI (CEA-IRFM)
-
10:15
-
10:45
→
11:00
Coffee Break 15m F23 Hall
F23 Hall
Frascati
-
11:00
→
12:30
WP Design Session Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy-
11:00
SPC TF winding pack design 15m
MAG-2.1-T025; MAG-2.3-T007
Speaker: Kamil Sedlak (EPFL-SPC, Switzerland) - 11:15
-
11:30
SPC CS coil design 15m
MAG-2.1-T025; MAG-2.3-T007
Speaker: Xabier Sarasola - 11:45
-
12:00
SPC PF coil design 15m
MAG-2.1-T025; MAG-2.3-T007
Speakers: Mithlesh Kumar, Roberto Guarino -
12:15
General discussion on TS 15mSpeaker: All
-
11:00
-
12:30
→
13:45
Lunch 1h 15m ENEA Canteen
ENEA Canteen
Frascati
-
13:45
→
15:00
Thermal-Hydraulic and Electromagnetic Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy-
13:45
SPC TF Thermal-hydraulic analysis 15m
MAG-2.2-T019
Speaker: Mithlesh Kumar -
14:00
CEA thermohydraulic analyses on DEMO TF design + CEA electromagnetic calc. 20m
MAG-2.2-T020; MAG-2.3-T008
Speaker: Roser Vallcorba + Louis Zani -
14:20
Support to the thermal-hydraulic design and analysis of the DEMO magnet system 15m
MAG-2.2-T018
Speaker: Laura Savoldi (Dipartimento Energia "Galileo Ferraris", Politecnico di Torino) -
14:35
IPPLM assessment of thermal hydraulic properties of Winding Packs for DEMO 15m
MAG-2.2-T017
Speaker: Monika Lewandowska -
14:50
General discussion on TS 10mSpeaker: All
-
13:45
-
15:00
→
15:30
Electric circuit, Feeders, Cryogenics, RAMI (MCD 2.4 - 2.6) Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy-
15:00
Studies on Fast Discharge Units – coil transient voltages 15m
MAG-2.4-T006
Speaker: Mattia Dan -
15:15
Cryogenic Studies on DEMO 15m
MAG-2.5-T008
Speaker: Christine Hoa (CEA/DRF/IRIG/DSBT)
-
15:00
-
15:30
→
15:45
Coffee Break 15m F23 Hall
F23 Hall
Frascati
-
15:45
→
17:00
Electric circuit, Feeders, Cryogenics, RAMI (MCD 2.4 - 2.6) Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy-
15:45
Sizing and preliminary design of feeders 10m
MAG-2.4-T007-D001
Speaker: Roberto Guarino -
15:55
Sizing and preliminary design of feeders 10m
MAG-2.4-T007-D002
Speaker: Laura Savoldi (Dipartimento Energia "Galileo Ferraris", Politecnico di Torino) -
16:05
Alternative TF current circuit (PMU task) 15m
PMI-2.1-T030
Speaker: Rainer Wesche (EPFL, Swiss PLasma Center) -
16:20
RAMI analysis of the DEMO magnet system 15m
MAG-2.6-T001
Speaker: roberto bonifetto (Politecnico di Torino) -
16:35
RAMI analysis of the cooling loop and He refrigerator 15m
MAG-2.6-T002
Speaker: Dario Carloni (UKAEA`) -
16:50
General discussion on TS 10mSpeaker: All
-
15:45
-
17:00
→
18:00
Other Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy-
17:00
Progress in the engineering grant activities 15mSpeaker: Bennet Jose (CEA Paris-Saclay)
-
17:15
Final report of the engineering grant 15mSpeaker: Roberto Bonifetto (Politecnico di Torino)
-
17:30
Engineering grant 2020 - introduction 15mSpeaker: Jose Lorenzo (Barcelona Supercomputing Center)
-
17:45
Engineering grant 2020 - introduction 15mSpeaker: Lorenzo Giannini (ENEA)
-
17:00
-
19:45
→
21:45
Common Dinner at Restaurant Cacciani - Frascati 2h Restaurant Cacciani
Restaurant Cacciani
Frascati
via armando Diaz 13-15 - Frascati
-
09:00
→
10:15
-
-
08:40
→
09:00
DTT Session - for everyone intersted Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy- 08:40
-
09:00
→
10:30
Mechanics & fabrication (MCD-3.1 & 3.2 & 3.3 & 3.4) Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy-
09:00
Coordination of the Mechanical Analysis 20m
MAG-3.1-T021
Speaker: Daniela Boso (University of Padova) -
09:20
Design of the mechanical structures and supports of the magnetic system 20m
MAG-3.1-T022
Speaker: Daniela Boso (University of Padova) -
09:40
Mechanical evaluation of TF coil and structure 15m
MAG-3.1-T018
Speaker: Francois NUNIO (CEA) -
09:55
Thermo-Mechanical Simulations 5m
MAG 3.2
Speaker: Francois NUNIO (CEA) -
10:00
Mechanical analyses of ENEA TF winding pack 2018 15m
MAG-3.1-T019
Speakers: Francesco Giorgetti (University of Tuscia), Giordano Tomassetti (ENEA) -
10:15
Mechanical analyses of CS coil 15m
MAG-3.1-T017
Speaker: Xabier Sarasola
-
09:00
-
10:30
→
10:45
Coffee Break 15m Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy -
10:45
→
11:30
Mechanics & fabrication (MCD-3.1 & 3.2 & 3.3 & 3.4) Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy-
10:45
CEA industry feasibility studies 15m
MAG-3.4-T008
Speaker: Louis ZANI (CEA-IRFM) -
11:00
Studies on manufact. process for cond. and winding of the DEMO hybrid CS coil 15m
MAG-3.4-T007
Speaker: Pierluigi Bruzzone (EPFL-SPC) -
11:15
General discussion on TS 15mSpeaker: All
-
10:45
-
11:30
→
12:30
R&D (MCD-4.2 & 4.3) Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy-
11:30
WPMAG19 CICC conductor sample cyclic mechanical performance test 15m
MAG-4.3-T020
Speaker: Arend Nijhuis (University of Twente) -
11:45
JackPot model R&D for conductor critical EM-thermal performance evaluation 15m
MAG-4.3-T021
Speaker: Arend Nijhuis (University of Twente) -
12:00
X-ray tomography on CICC conductors and joints 15m
MAG-4.3-T022
Speaker: Ion Tiseanu (National Institute for Lasers, Plasma and Radiation Physics (INFLPR)) - 12:15
-
11:30
-
12:30
→
13:45
Lunch 1h 15m Canteen
Canteen
Frascati
-
13:45
→
15:50
R&D (MCD-4.2 & 4.3) Bruno Brunelli Hall
Bruno Brunelli Hall
Frascati
ENEA - Research Centre Via Enrico Fermi, 45 Frascati, Italy-
13:45
Test of RW2 prototype with cabled stabilizer 15m
MAG-4.2-T011
Speaker: Pierluigi Bruzzone (EPFL-SPC) -
14:00
Test of TF prototype joint 20m
MAG-4.2-T011
Speaker: Vincenzo D'Auria (Swiss Plasma Center - École polytechnique fédérale de Lausanne) -
14:20
ENEA sample tests 15m
MAG-4.3-T024
Speaker: Luigi Muzzi (ENEA) -
14:35
Design and preparatory work to host the new EDIPO test facility 15m
MAG-4.3-T025
Speaker: Xabier Sarasola -
14:50
General discussion on TS 15mSpeaker: All
-
15:05
2019 WPMAG activities: meeting conclusions 30mSpeaker: All
-
13:45
-
08:40
→
09:00